Intelligence Plastic Injection Production to Accelerate Post-Pandemic Recovery

  • Event:Intelligence Plastic Injection production to accelerate Post-Pandemic Recovery
  • Organized by:
    • ACMT Indonesia Smart Manufacturing Alliance(ACMT-ISMA)
    • Jakarta Taiwan Entrepreneur Associate(JTEA)
  • Co-organizer:
    • Ministry of Industry, Indonesia
    • Minnotec
    • Chung Yuan Christian University, R&D Center for Smart Manufacturing (CYCU SMC)
    • Atma Jaya Catholic University
  • Date:2021/12/21(TUE)
TimeSubject
(ID)13:30
(TW)14:30
Registration
(ID)13:35
(TW)14:35
Welcome Speech
Iken Retnowulan, Director of Industrial Resource Access and International promotion, Ministry of Industry, Indonesia
Chin Chia-Sheng, Chairman of Jakarta Taiwan Entrepreneur Associate, JTEA
Vito Tsai, President of Association of CAE Molding Technology
(ID)13:50
(TW)14:50
Introduction of ACMT-ISMA
(ACMT-Indonesia Smart Manufacturing Alliance, Hariyanto Gunawan)
(ID)14:00
(TW)15:00
Development and Application of Intelligent Injection Machine Networking System
(Minnotec, Steve Tang)
(ID)14:20
(TW)15:20
The Future of Indonesia’s Plastic
(R. Janu Suryanto, Head of data and information center, Ministry of Industry, Indonesia )
(ID)14:40
(TW)15:40
Mold T-zero Mass Production and 3-in-1 Engineer Training
(ACMT, Vito Tsai)
(ID)15:00
(TW)16:00
New Generation Mold Management System Development and Application
(T-Mold, Benson Yang)
(ID)15:20
(TW)16:20
Conclusion

VIP-Opening Remarks

Mold T-zero Mass Production and 3-in-1 Engineer Training

Mr. Vito Tsai

  • President of ACMT
  • President of Minnotec Co., Ltd.

Experience

  • 1989, Programmer of Moldex Software ( NTHU )
  • 1995, One of the founders of Moldex3D (Coretech)
  • 2004, Founding secretary-general of ACMT
  • 2006, Moldex3D General Manager, Greater China
  • 2016, President of ACMT

Speaker

Dr. Hariyanto Gunawan (Harry Wey)

  • Assistant Professor, Mechanical Engineering Dept., Chung Yuan Christian University
  • Consultant, Office of International Affairs, CYCU

Research interest

  • Digital manufacturing, Intelligent manufacturing, real time monitoring, machine tool, Artificial Intelligent, machine learning, big data analysis, internet of things, application of Industry 4.0, smart material, Augmented Reality, piezoelectric ceramic & polymer.

Development and Application of Intelligent Injection Machine Networking System

Mr. Steve Tang

  • Molding Innovation Technology Co., Ltd (Minnotec) / Vice President
  • Association of CAE Molding Technology (ACMT) / Secretary General

Experience

  • National Taipei University of Technology / Department of Chemical Engineering Technology / bachelor
  • National Chin-Yi University of Technology / Department of Materials and Chemical Engineering / Master
  • Chung Yuan Christian University / Department of Mechanical Engineering / Ph.D. Candidate
  • CoreTech System Co., Ltd. (Moldex3D) / Project Manager / 1999-2005
  • DragonJet Corporation (LITE-ON GROUP) / Director of R&D / 2005-2015

New Generation Mold Management System Development and Application

Mr. Benson Yang

  • Molding Innovation Technology Co., Ltd (Minnotec) / Senior Application Consultant
  • Association of CAE Molding Technology (ACMT) / Senior Project Manager

Experience

  • National Cheng Kung University / Polymeric Materials Laboratory / Master
  • Integrated Software Development of Colour 3D Printing System / Software Development
  • Research and Development of Polymeric Materials Industry Engineering / Mold Engineering
  • Application Consulting Service of Moldex3D / Sales Manager
  • Project Integration of Smart Factory / Project Manager

Indonesia Contact

Hariyanto Gunawan (Harry Wey) (Ph.D)

TEL:+62-851-3216-4159

E-Mail:harry.wey@caemolding.org

Taiwan Contact

Nina Fan 范馨予

TEL:+886-2-8969-0409 #220

E-Mail:nina.fan@caemolding.org

發佈留言

發佈留言必須填寫的電子郵件地址不會公開。 必填欄位標示為 *